Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
Pete writes: This video shows the LBS XCVR shrunk down to a mainboard that is 2.5 Inches by 4.5 inches. The board contains the 20 Meter Band Pass Filter, the RxTx Mixer, a TUF-3, two bilateral amplifier stages a 5.185 MHz Homebrew Filter. a TUF-3 PD/BM. The Audio amp stage and the microphone amp. Not built as yet is the bi-directional stage that on receive is the RF amp and on transmit the Tx pre-driver stage. Extensive use of SMD components makes the size reduction possible. The transmit final stages will be on a 2nd board that is stacked on top of the mainboard. An Arduino Pro-Mini does all of the control for the Si5351 VFO/BFO. The final size will be 4X6X2. Oh it also has a color display! http://www.n6qw.com/.
Would using ADE-1 surface mount mixers make the circuit even more compact? I'd like to get into using SMD/SMT. Perhaps Pete would do an article or talk to help the scared and wary amongst us, myself included take the leap into the unknown?
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Re: Another vote for the LP100A
-
I have an LP100. Amazing meter.
Also have a powermaster and a few Birds, including digital Birds.
The LP100 (and powermaster) are always in agreement with...
No birds do sing
-
Hi FastRadioBurst 23 here letting you know of our forthcoming shows this
week. On Sunday 21st April 2024 at 0900/1300 hrs UTC on 6160 kHz and then
at 2000 ...
An Inline RF Step Attenuator for QRPp Work
-
I don’t need to explain the attraction of low power operation; if you’re
reading this, the chances are that you are already a convert. I’ve been
operating ...
Using an external clock with the RX-888 (Mk2)
-
*The RX-888 (Mk2) and external clocking*
*Figure 1:*
The RX-888 with external clock input *(right)*
The enable/disable switch is barely
visible behind the...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
Would using ADE-1 surface mount mixers make the circuit even more compact? I'd like to get into using SMD/SMT. Perhaps Pete would do an article or talk to help the scared and wary amongst us, myself included take the leap into the unknown?
ReplyDeleteThree common misconceptions of many new radio home builders:
ReplyDelete[1] Toroidal inductor and transformers are difficult to make
[2] Measurement ranks unimportant and is only for geeks
[3] SMT soldering is difficult
[3] ------------------>
For a quick SMT soldering primer consider:
http://ve7sl.blogspot.ca/2014/07/more-smt-talk.html
Then search online for the ton of tutorials and videos.
1 SMT soldering primer from a pro engineer I follow and recommend :
https://www.youtube.com/watch?v=b9FC9fAlfQE
----------------------------------------------------------------------------
Drop by our solid state homebrew regen community:
https://plus.google.com/communities/111700710411953988036
Thanks Bill, Pete and World
Todd/Vasily
http://qrp-popcorn.blogspot.ca/